Phone: (718) 507-8844   Fax: (718) 565-6018
Email: info@irauch.com
Address: 32-20 112th St, East Elmhurst, NY 11369

Search Results

Sort by:

Fig 81
Split Ring Hanger
General piping.

Fig 800
Adjustable Swivel Ring
General piping.

Fig 1A
Band Hanger
General piping.

Fig 1ASH
Band Hanger with Shield
Use on vapor sealed lines.

Fig 100
Clevis Hanger
General piping.

Fig 200VT
V-Trough Clevis Hanger
Designed for the support of plastic pipe. Fig 200VT Hanger is intended for use with our Fig 201 V-Tr...

Fig 200
L.D. Clevis Hanger
General piping.

Fig 100F
Flat Top Clevis Hanger
General piping. Where space does not permit installation of standard Fig 100 Clevis Hangers.

Fig 100SH
Clevis Hanger with Welded Shield
For vapor sealed lines.

Fig 100S
Clevis Hanger with Welded Saddle
Designed to properly support insulated lines not subject to Longitudinal Movement.

Fig 100EL
Elongated Clevis Hanger
Where contractor is permitted to cover both pipe and hanger, the additional depth of bottom yoke wil...

Fig 237
One-Hole Pipe Clamp

Fig 283
Standard U-Bolt
General piping.

Fig 223
Light Duty U-Bolt
General piping.

Fig 222
Stack Hanger
Fig 222 is designed for the support of cast iron stack fittings in high rise construction. The angle...

Fig 140
Clevis Roller Hanger
Designed for use on lines subject to Longitudinal Movement.

Fig 142
Two-Rod Roller Hanger
For suspension of pipe where longitudinal movement due to expansion and contraction may occur.

Fig 110
Adjustable Roller Support
Designed for use on lines subject to Longitudinal Movement.

Fig 111
Adjustable Roller Support Short Pattern
Designed for use on lines subject to Longitudinal Movement.

Fig 109
Adjustable Two-Rod Roller Support
Designed for use on lines subject to Longitudinal Movement.

Fig 54
Roller Chair
Designed for use on lines subject to Longitudinal Movement.

Fig 41
Pipe Roll and Steel Base
Designed for use on lines subject to Longitudinal Movement.

Fig 39
Steel Chair and Roll
Designed for use on lines subject to Longitudinal Movement.

Fig 40
Adjustable Steel Chair and Roll
Designed for use on lines subject to Longitudinal Movement.

Fig 333
Roller Support
The adjustment of the pipe line is had by turning the top nut which raises or lowers the pipe to des...

Fig 71
Roller Support
Designed for use on lines subject to Longitudinal Movement.

Fig 265CVB
180-Degree Shield with Insulation Saddle
For installation on vapor-sealed lines. Excellent for low-temperature installations. A molded secti...

Fig 265P
180-Degree Pipe-Covering Protection Shield
Recommended for outside of foam or fiber glass.

Fig 269
360-Degree Pipe-Covering Protection Shield
For vapor-sealed lines.

Fig 351
1-Inch Pipe-Covering Protection Saddle
Designed for high-temperature service where heat losses are to be kept at a minimum and to protect i...

Fig 352
1-1/2-Inch Pipe-Covering Protection Saddle
Designed for high-temperature service where heat losses are to be kept at a minimum and to protect i...

Fig 126
Riser Clamp - Equal Arms
Support of steel or cast iron pipe risers.

Fig 129
Short Arm Riser Clamp
General piping.

Fig 353
2-Inch Pipe-Covering Protection Saddles
Designed for high-temperature service where heat losses are to be kept at a minimum and to protect i...

Fig 354
2-1/2-Inch Pipe-Covering Protection Saddle
Designed for high-temperature service where heat losses are to be kept at a minimum and to protect i...

Fig 355
3-Inch Pipe-Covering Protection Saddle
Designed for high-temperature service where heat losses are to be kept at a minimum and to protect i...

Fig 356
4-Inch Pipe-Covering Protection Saddle
Designed for high-temperature service where heat losses are to be kept at a minimum and to protect i...

Fig 175
Standard Steel Pipe Clamp
General piping.

Fig 304
Double Bolt Pipe Clamp
Recommended for suspension of insulated pipe.

Fig 298
Heavy Steel Pipe Clamp
Recommended for suspension of heavy loads.

Fig 89
Long and Short Art Riser Clamp
Support of steel or cast iron pipe risers.

Fig 128
Multiple Riser Clamp
General piping.

Fig 157
Underground Pipe Hanger
To support underground drainage lines. Clamps tight on cast iron pipe and maintains anchor bolt in p...

Fig 179
Offset Pipe Clamp
To support general piping, running from wall or floor. This clamp can be furnished with "E" dimensio...

Fig 267
Extended Pipe Clamp
General piping. Designed for direct welding of hanger to steel structure.

Fig 156
Four-Section Rodding Band
To avoid possibility of joints blowing out on high-pressure cast iron water mains. Made to City of N...

Fig 158
Corporation Clamp
Designed to restrain the caulked joints on cast iron Bell and Spigot water mains. Corporation Clamp ...

Fig 114
Short Clip
Recommended for use as a hanger from walls or ceilings where piping is run close to the structure. S...

Fig 72
Pipe Clip

Fig 227
Offset J-Hook
For general piping running next to wall.

Fig 227S
Straight J-Hook
For general piping running next to wall.

Fig 221
Wall Pipe Support
For general piping running next to wall.

Fig 228
Hook Plate
Offset hook plates are furnished in various lengths. Any number of hooks can be furnished per plate.

Fig 145
Pipe Chair
General piping.

Fig 137
Adjustable Pipe Saddle Support
Adjustable Pipe Supports are used in conjunction with a pipe standard and flange at the base, to sup...

Fig 136
Pipe Saddle Support
For general piping running close to floor.

Fig 247
Adjustable Pipe Saddle Support with Coupling
For general piping running close to floor.

Fig 127A
Anchor Chair
For use on welded steel brackets or structural member.

Fig 127B
Anchor Chair
For use on welded steel brackets or structural member.

Fig 250
Base Elbow Support
General piping.

Fig 251
Adjustable Base Elbow Support
General piping.

Fig 245
Pipe Saddle Support
For general piping running close to the floor.

Fig 101
Adjustable Pipe Saddle Support
For general piping running close to the floor.

Fig 249
Adjustable Slide Pipe Stanchion
For general piping running close to the floor. Structure support is provided by heavy gauge sections...

Fig 125
Pipe Saddle Support with U-Bolt
For general piping running close to the floor.

Fig 1008
Cylinder Pipe Guide (Solid)
Cylinder type pipe alignment guides, solid or split, provide a most compact, economical and positive...

Fig 1007
Cylinder Pipe Guide (Split)
Cylinder type pipe alignment guides, solid or split, provide a most compact, economical and positive...

Fig 248
Adjustable Pipe Stanchion Roller Support
For general piping running close to floor.

Fig 124
Adjustable Pipe Saddle Support with U-Bolt
For general piping running close to the floor.

Fig 246
Pipe Stanchion Roller Support
For general piping running close to the floor.

Fig 374
Angle Trapeze Hanger
General piping.

Fig 371
Channel Trapeze Hanger
General piping.

Fig 148
Malleable Adjustable Beam Clamp
Recommended for attachment to bottom flange of I-beams and wide flange beams where flange widths are...

Fig 100CT
Copper Coated Clevis Hanger
General piping.

Fig 1ACT
Copper Coated Band Hanager
General piping.

Fig 81CT
Copper Coated Split Ring Hanger
General piping.

Fig 126CT
Copper Coated Riser Clamp

Fig 800CT
Copper Coated Swivel Hanger
General piping.

Fig 100PVC
Plastic Coated Hanger
For use with noninsulated copper tubing, glass, aluminum and brass pipe. Maximum Operating Temperatu...

Fig 800PVC
Plastic Coated Hanger
For use with noninsulated copper tubing, glass, aluminum and brass pipe. Maximum Operating Temperatu...

Fig 1APVC
Plastic Coated Hanger
For use with noninsulated copper tubing, glass, aluminum and brass pipe. Maximum Operating Temperatu...

Fig 126PVC
Plastic Coated Clamp
For use with noninsulated copper tubing, glass, aluminum and brass pipe. Maximum Operating Temperatu...